Labware Products & Reviews

This 3-ball PYREX® Snyder column has a 24/40 Standard Taper inner joint on the lower end and a 24/40 Standard Taper outer joint on the upper end.

This complete 500 mL PYREX® Kuderna-Danish Concentrator apparatus consists of a 3-ball Snyder column with 24/40 Standard Taper joints (2158-3CO), a 500 mL flask with a 24/40 outer Standard Taper upper joint and 19/22 inner Standard Taper lower joint, and a 10 mL graduated tube with 19/22 outer Standard Taper joint. The tube graduations go from 0 to 2 mL in 0.1 mL increments and from 3 mL on in 1.0 mL increments. If further con…

This 500 mL PYREX® replacement Kuderna-Danish flask has a 24/40 outer Standard Taper upper joint and 19/22 inner Standard Taper lower joint and includes a pair of 1 1/4 inch stainless steel springs and two sizes of Keck clamps.

Brand: PYREX®

These 1L PYREX® blunt tip cones are for use with heavy sediments, where ability to read small volumes is unimportant. Graduated from 0 to 1 mL in 0.1 mL divisions, 1 to 10 mL in 0.5 mL and 10 to 40 mL in 1 mL; also marked at 1000 mL. The blunt tip increases its ruggedness and cleaning ease.

This PYREX® general purpose condenser has a 24/40 Standard Taper inner joint at the bottom with a drip tip. Although the condensing area per unit length of the 400mm long jacket is low, the large capacity water jacket gives efficient cooling. They can be used for either distillation or extraction. Condenser tubulations are approximately 10mm O.D.

This PYREX® general purpose condenser has a 24/40 Standard Taper inner joint at the bottom with a drip tip. Although the condensing area per unit length of the 500mm long jacket is low, the large capacity water jacket gives efficient cooling. They can be used for either distillation or extraction. Condenser tubulations are approximately 10mm O.D.

10 µm thick transparent polyester membrane Treated for optimal cell attachment Packaged 12 inserts in a 24 well plate, 4 plates per case Excellent visibility under phase contrast microscopy Sterilized by gamma radiation

These PYREX® Liebig condensers have a 300mm long condenser jacket with a 24/40 Standard Taper outer joint at the top and a 24/40 Standard Taper inner joint at the bottom with a drip tip. They are general purpose condensers that are suitable for use in vacuum distillations. Condenser tubulations are approximately 10mm O.D.

10 µm thick transparent polyester membrane Treated for optimal cell attachment Packaged 12 inserts in a 24 well plate, 4 plates per case Excellent visibility under phase contrast microscopy Sterilized by gamma radiation

Brand: PYREX®

This Jacketed Reflux Condenser is a replacement part for the 6949M series of PYREX® microchemistry kits.

This Jacketed Reflux Condenser is a replacement part for the 6949M series of PYREX® microchemistry kits.

This Jacketed Reflux Condenser is a replacement part for the 6949M series of PYREX® microchemistry kits.

These widely used 3 bulb PYREX® condensers have a greater surface area than the corresponding Liebig type and are suitable for use in vacuum distillations. They have an outer 19/38 Standard Taper joint at the top and an inner 19/38 Standard Taper joint at the bottom with a drip tip. The tubulations have an O.D. of approximately 10mm.

These widely used 5 bulb PYREX® condensers have a greater surface area than the corresponding Liebig type and are suitable for use in vacuum distillations. They have an outer 24/40 Standard Taper joint at the top and an inner 24/40 Standard Taper joint at the bottom with a drip tip. The tubulations have an O.D. of approximately 10mm.

These widely used 6 bulb PYREX® condensers have a greater surface area than the corresponding Liebig type and are suitable for use in vacuum distillations. They have an outer 24/40 Standard Taper joint at the top and an inner 24/40 Standard Taper joint at the bottom with a drip tip. The tubulations have an O.D. of approximately 10mm.

These widely used 8 bulb PYREX® condensers have a greater surface area than the corresponding Liebig type and are suitable for use in vacuum distillations. They have an outer 24/40 Standard Taper joint at the top and an inner 24/40 Standard Taper joint at the bottom with a drip tip. The tubulations have an O.D. of approximately 10mm.

These widely used 10 bulb PYREX® condensers have a greater surface area than the corresponding Liebig type and are suitable for use in vacuum distillations. They have an outer 29/42 Standard Taper joint at the top and an inner 29/42 Standard Taper joint at the bottom with a drip tip. The tubulations have an O.D. of approximately 10mm.

Brand: PYREX®

These PYREX® condensers have a high surface area per unit length of the 200mm long jacket with a 19/38 Standard Taper outer joint at the top and a plain drip tip at the bottom. They are primarily used in distillation assemblies. Condenser tubulations are approximately 10mm O.D.

Brand: PYREX®

Secure stacking provides stability from accidental tips or spills, and protection against contamination (canted neck flasks)Nonpyrogenic tested to less than 0.1 EU/ mLVolumetric graduations and writing patchGrowth area and volume are nominal

These PYREX® Graham condensers have a high surface area per unit length of the 300mm long jacket with a 24/40 Standard Taper outer joint at the top and a 24/40 Standard Taper inner joint at the bottom with a drip tip. They are primarily used in vacuum distillations. Condenser tubulations are approximately 10mm O.D.

Secure stacking provides stability from accidental tips or spills, and protection against contamination (canted neck flasks)Nonpyrogenic tested to less than 0.1 EU/ mLVolumetric graduations and writing patchGrowth area and volume are nominal