Separations is a fundamental scientific discipline focused on the isolation and purification of components from mixtures. Through techniques such as chromatography, distillation, and filtration, separations scientists separate substances based on their physical or chemical properties. This field plays a crucial role in various industries, including pharmaceuticals, food and beverage testing, environmental science, materials research, and more. Explore how separations techniques enable precise analysis, quality control, and the development of innovative products.
SDB-XC is a poly(styrenedivinylbenzene) copolymer used as a reversed phase sorbent for solid phase extraction. SDB-XC is not bonded to silica but is a 100% copolymeric particle that is spherical, porous and cross-linked. It does not exhibit the secondary cationic (silanol) interactions and pH limitations common to bonded silica sorbents, so it offers more predictable and reproducible reversed phase interaction.
The Empore™ High Performance Extraction Disk Plate differs in design from plates offered by other manufacturers and requires a specific vacuum manifold. Manifolds supplied by different plate manufacturers are specific to the design of their plates and cannot generally be used with plates from other manufacturers. In some cases, the use of spacers to raise/lower the height of a collection device inside the manifold may overco…
Replacement gaskets are available with the vacuum manifold assembly. The gasket can become worn over time and the seal between the plate and the manifold will be affected. This may result in poor vacuum pressure and negatively effect flow rates. The gasket should be checked regularly and replaced when it becomes worn.
EmporeTM Tape Pads are intended for sealing unused portions of a 96-well solid phase extraction plate during vacuum processing to enable vacuum to be uniformly applied to each well being used. Use a clean sheet each time for maximum sealing ability. Note: these tape sheets are not intended for sealing collection plates prior to sample injection because the adhesive may clog the injection needle.
Empore Filter Aid 400 has been shown to improve flow rates and recoveries for separation and filtration of water samples containing suspended solids. When placed on top of the Empore™ Extraction Disk at a depth of about 1 cm, Empore™ Filter Aid 400 acts as depth filter to inhibit the migration of suspended solids to the surface of the disk. This reduces extraction time and improves rates and recovery of analytes.
The CycloGraph system is a centrifugally accelerated device for performing preparative thin layer radial separations. The separations occur quickly (within 20 minutes) with no need for scraping separated bands as with traditional Thin Layer Chromatography. Principle of Operation The compound to be separated is applied as a solution inside the adsorbent ring of the pre-cast Rotor (Analtechs prepared consumable for this device)…
Silica Gel G & GF UNIPLATES are the most widely used silica gel TLC plates. No organic substances are added to these products, thus making them compatible with sulphuric acid charring visualization. These plates are commonly scraped from the glass backing to isolate separated components for other analytical procedures.
Silica Gel G & GF UNIPLATES are the most widely used silica gel TLC plates. No organic substances are added to these products, thus making them compatible with sulphuric acid charring visualization. These plates are commonly scraped from the glass backing to isolate separated components for other analytical procedures.
Silica Gel G & GF UNIPLATES are the most widely used silica gel TLC plates. No organic substances are added to these products, thus making them compatible with sulphuric acid charring visualization. These plates are commonly scraped from the glass backing to isolate separated components for other analytical procedures.
Analtech Reversed Phase Separation (RPS) UNIPLATES offers several advantages over the bonded RP18 type TLC plates. RBS UNIPLATES are a hydrocarbon impregnated silica gel. The hydrocarbon is adsorbed onto the silica gel surface and is not chemically anchored to the particle. The main advantages of the hydrocarbon impregnated Reversed Phase plate are compatibility with aqueous solutions and parallel behavior to most C18 HPLC pac…
The UNIPLATE-T Taper Plate, invented and patented by Analtech, is a unique preparative TLC plate that provides unusually high resolution for a preparative layer. It has a wedge-shaped adsorbent layer, progressing from 300 microns (bottom) to 1700 microns (top). Below the silica layer is a 700-micron-thick pre-absorbent zone provided for easier sample application and higher sample resolution.
Analtech's glass TLC developing chambers provide optimum developing conditions for a variety of TLC plate sizes and shapes. Precision ground surfaces provide tight seals between tanks and glass covers, permitting complete saturation of chambers with solvent vapour for uniform development of chromatograms.
Analtech's glass TLC developing chambers provide optimum developing conditions for a variety of TLC plate sizes and shapes. Precision ground surfaces provide tight seals between tanks and glass covers and permit complete saturation of chambers with solvent vapour for uniform development of chromatograms
The TLC AUTOSPOTTER is a semi-automated device used to apply samples on Thin Layer Chromatography plates. The instrument eliminates the need for manual sample application and can be used to apply up to 18 samples at a time.
Spark has introduced the second edition of HySphere™ C8 End-Capped cartridges. We have selected a new perfect Spherical sorbent material with a narrow particle size distribution. This will create less back pressure during operation and allows you to run higher flow rates compared to our current HySphere™ C8 (EC). The new cartridge has the same excellent characteristics such as high extraction capacity and selectivity
Fits plastic or glass media bottles with 33mm neck sizes. Cellulose acetate (CA) membranes provide fast flow rates and low protein binding and are good for filtering cell culture media. Angled hose connector simplifies vacuum line attachment. Individually packaged, sterile and certified nonpyrogenic. Each system has the membrane material and pore size printed on the unit and is color-coded by membrane type for easy produ…
The XTRX ™ columns can be used for everything from drug testing to environmental pollutants screenings and is designed for use in the Dupont Prep ™ 1 Automated Sample Processor, the XTRX ™ 4 Automated Sample Processor or any vacuum box. The XTRX ™ columns were previously manufactured by Creative Technology Systems, Inc. Since 1961 Analtech has been manufacturing quality thin layer chromatography plates, providing friendly and…
VICI introduces the GC detector where the PDD (pulsed discharge detector) utilizes a stable, low-powered, pulsed DC discharge in helium as the ionization source. The D-2 is a dual mode, universal detector system which can be retrofitted to your older GC. The D-2-I is a helium photoionization detector, optimized for trace level work with packed columns. The stand-alone systems include detector, controller, electrometer, helium…
Pulsed discharge detector Model D-3 is designed for plug-and-play installation on Agilent GC's, with models available for the 6890 and 7890. The D-3 is optimized for trace level work in the helium photoionization mode, and utilizes the electronics and power supply of the host GC. Model D-5 is optimized for electron capture detection. Available for 110 VAC and 230 VAC.
Model D-5 is a pulse discharge GC detector designed for plug-and-play installation on the Agilent 6890. The D-5 is optimized for trace level work in the electron capture mode, and utilizes the electronics and power supply of the host 6890. Model D-3 is optimized for helium photoionization detection. Available for 110 VAC and 230 VAC.
Model D-4 a GC Detector available in versions for easy installation on most of the GC's in current use, including the Varian 3800, Shimadzu 14 and 17, ThermoFinnigan Trace, Mega, and Top, and Hewlett Packard 5890. The D-4 is single mode, optimized for trace level work in the helium photoionization mode. Available for 110 VAC and 230 VAC.
Model D-6 is a single mode GC detector, optimized for trace level work in the electron capture mode. IT is available in versions for easy installation on most of the GC's in current use, including the Varian 3800, Shimadzu 17, ThermoFinnigan Trace, Mega, and Top, and Hewlett Packard 5890. Available for 110 VAC and 230 VAC.
Reduced breakdown liners Our improved injection port liner reduces breakdown of endrin and DDT during injections while increasing the interval between liner changes. The problem DDT and Endrin are easily degraded in the injection port; with non-deactivated liners and those filled with non-deactivated glass wool, Endrin breakdown can be as high as 98%. EPA method 8081A states "If degradation of either DDT or Endrin exceeds 15%,…
VICI AG uses proprietary liquid phase processing to produce low bleed characteristics while maintaining identical retention characteristics to the phases you are used to. These processes combined with proprietary coating, curing, bonding, and crosslinking produce MS-certified bleed characteristics equal to the best. Improved upper temperature limits enhance column "bake out", reducing sample carryover and cycle times. ValcoBon…
Now you can reduce run time, faster than micropacked, by replacing your packed columns with ValcoPLOT HayeSep capillary PLOT columns, with phases available only from VICI. Our proprietary phase processing produces the first capillary PLOT columns with characteristics identical to HayeSep packed columns. The ValcoPLOT line also includes Molesieve and Alumina PLOT columns. Visit VICI AG website to veiw now.
