Automation Supplies / Accessories Products & Reviews

A 140 µm thick hydrophobic porous rayon sealing film including medical-grade adhesive for tissue culture plates, bio-blocks, and 96-well plates where gas exchange is necessary for cell or bacterial growth. AeraSeal sealing films minimize cross-contamination, spillage and evaporation. They allow uniform air and CO2 exchange for all wells, unlike plate lids which favor exchange for wells near the plate edges. Dimensions: 82.6 by…

Easily pierceable, 70 µm thick, polyethylene with acrylic adhesive, EZ-PierceTM sealing films allow direct sample recovery with single or multichannel pipettors and robotic probes. Dimensions are 82.6 by 142.9 mm for 96-well plates.Features:easily pierceable with pipet tips or robotic probesinert, chemical resistantfunctional temperature range -40°C to +90°C

Easily pierceable, 70 µm thick, polyethylene with acrylic adhesive, EZ-PierceTM sealing films allow direct sample recovery with single or multichannel pipettors and robotic probes. Dimensions are 82.6 by 142.9 mm for 96-well plates.Features:easily pierceable with pipet tips or robotic probesinert, chemical resistantfunctional temperature range -40°C to +90°C

X-PierceTM sealing films are 89 µm thick vinyl with a 18 µm thick adhesive layer, designed for temporary protection from contamination and evaporation for samples in 96-well plates. A precut "X" over each well creates four flaps that easily bend downward when pushed by a robotic probe or pipet tip, allowing sample access without coring or adhesive fouling. A thin adhesive layer and special hairline cuts separating the X-Pierce…

With a 70 µm polyethylene top layer and inert white polypropylene and acrylic adhesive sublayer, this easy-piercing sealing film allows direct sample recovery with single or multichannel pipettors and robotic probes. The adhesive-free zone above each well prevents adhesive fouling of the pipet tip or probe, ultimately minimizing the amount of adhesive that comes into contact with the sample. Dimensions are 79.4 by 142.9 mm for…

BrightMaxTM sealing films are 203 µm thick white vinyl films with 37 µm acrylic adhesive for use with white microplates. The sealing films may be applied to either the top or bottom of the plate. A split backing aids in applying the sealing film properly. The light-reflective properties of BrightMax plate-sealing films on clear-bottom plates maximize sensitivity of bioluminescence and chemiluminscence assays in bottom-reading…

AbsorbMaxTM sealing films are 203 µm thick black vinyl films with 37 µm acrylic adhesive for use with 96-well, 384-well, and 1536-well black microplates. The sealing films may be applied to either the top or bottom of the plate. A split backing aids in applying the sealing film properly. Edge cutouts assist in positioning and accomodate ribs on the plate bottom. The light-blocking and absorbing properties of AbsorbMax sealing…

Evenly applies film on raised rim plates.

A 48 um soft non-permeable aluminum foil sealing film with 30 um layer of strong acrylic adhesive. FoilSealTM sealing foils remove cleanly from plate surfaces with no adhesive stringing, residue or contamination. Each sealing foil measures 78.3 x 129 mm and offers sufficient sealing area for all plate types (e.g. flat top and raised-rim). Chamfered corners result in no plate overhang for robotics applications. Features one end…

eXTReme™ Seal features an extra-strong, thick adhesive to minimize evaporation yet removes easily without leaving residue on the plate.

eXTReme™ Seal features an extra-strong, thick adhesive to minimize evaporation yet removes easily without leaving residue on the plate.

Resistant to Xylene, MEK, IPA, DMSO and many more, Laboratory Labelling Specialists CILS have launched the ultimate solvent-resistant, computer printable durable label – ideal for microscope slides, HPLC columns, tissue cassettes, vials, tubes etc. Printable straight from a standard Laser or Thermal Transfer, variable data (batch no’s, barcodes etc) can be added ‘in minutes’, saving time and eliminating the risk of smudged/ill…

384 well plate for the determination of protein binding on HSAconfiguration: 93 compounds1 reference/ 3 TRANSIL® - HSA concentrations per compound

Reagent Reservoir Rack for placing reagent tubs.

The MagNA Pure LC Barcode Printer TLP 2844 facilitates sample identification, tracking, and documentation during MagNA Pure LC purification runs. It enables the user to print bar codes created by the MagNA Pure LC Software Version 3.0 for the MagNA Pure LC Sample Cartridges and/or non-barcode-labeled primary tubes. The MagNA Pure LC Barcode Labels (available separately, Cat. No. 03 531 520 001) are suitable for the new bar-cod…

MicroLiter was founded in 1996 to supply autosampler vials and consumables for the industry’s leading autosamplers. In 2012, MicroLiter became part of the WHEATON family of products.Since inception, MicroLiter has made the fundamental decision to only offer products that offered proven stable performance and to avoid those products that had a wide range of tolerances which could impede the performance of the autosampler.In add…

(This is the suggested replacement for 2480) Stripwell™ Low Volume Microplates are designed with one-half the well area of a “regular” 8-well strip, providing a much greater surface to volume ratio. Low volume wells have recommended working volume of 50 to 125 µL May be used in a variety of laboratory assays Flat bottom strips are designed to easily break apart and are pre-assembled in an egg-crate style strip holder that…

Stripwell™ Low Volume Microplates are designed with one-half the well area of a “regular” 8-well strip, providing a much greater surface to volume ratio. Low volume wells have recommended working volume of 50 to 125 µL May be used in a variety of laboratory assays Flat bottom strips are designed to easily break apart and are pre-assembled in an style strip holder that allows each individual well to be positioned back into…

Stripwell™ Low Volume Microplates are designed with one-half the well area of a “regular” 8-well strip, providing a much greater surface to volume ratio. Low volume wells have recommended working volume of 50 to 125 µL May be used in a variety of laboratory assays Flat bottom strips are designed to easily break apart and are pre-assembled in an style strip holder that allows each individual well to be positioned back into…

Stripwell™ Low Volume Microplates are designed with one-half the well area of a “regular” 8-well strip, providing a much greater surface to volume ratio. Low volume wells have recommended working volume of 50 to 125 µL May be used in a variety of laboratory assays Flat bottom strips are designed to easily break apart and are pre-assembled in an style strip holder that allows each individual well to be positioned back into…

Stripwell™ Low Volume Microplates are designed with one-half the well area of a “regular” 8-well strip, providing a much greater surface to volume ratio. Low volume wells have recommended working volume of 50 to 125 µL May be used in a variety of laboratory assays Flat bottom strips are designed to easily break apart and are pre-assembled in an style strip holder that allows each individual well to be positioned back into…

May be used in a variety of laboratory assays Flat bottom strips are designed to easily break apart and are pre-assembled in an style strip holder that allows each individual well to be positioned back into the plate once broken White wells enhance luminescent signals, have low background luminescence and fluorescence, and prevent well-to-well crosstalk Not treated (or medium binding) polystyrene surface is hydrophobic in…

May be used in a variety of laboratory assays Flat bottom strips are designed to easily break apart and are pre-assembled in an style strip holder that allows each individual well to be positioned back into the plate once broken Black wells have low background fluorescence, minimal light scatter and reduced crosstalk Not treated (or medium binding) polystyrene surface is hydrophobic in nature and binds biomolecules throug…

May be used in a variety of laboratory assays Flat bottom strips are designed to easily break apart and are pre-assembled in an style strip holder that allows each individual well to be positioned back into the plate once broken White wells enhance luminescent signals, have low background luminescence and fluorescence, and prevent well-to-well crosstalk High binding surface binds medium (>10kD) and large biomolecules that…

May be used in a variety of laboratory assays Flat bottom strips are designed to easily break apart and are pre-assembled in an style strip holder that allows each individual well to be positioned back into the plate once broken Black wells have low background fluorescence, minimal light scatter and reduced crosstalk High binding surface binds medium (>10kD) and large biomolecules that possess ionic groups and/or hydropho…